Why Roof Leaks Around Skylights and Chimneys Usually Point to Step Flashing—Not the Glass

When a brown water ring blooms across a ceiling beside a skylight or along the drywall framing a fireplace hearth, most homeowners immediately blame the skylight glass or cracked chimney mortar. That reaction makes intuitive sense—a pane of glass sitting in the middle of a roof looks vulnerable, and aging brickwork naturally draws scrutiny.

Yet when experienced roofers climb onto the roof to trace the path of water intrusion, the glass itself is rarely the culprit. In the overwhelming majority of cases, moisture sneaks inside along the intersection between the sloped roof deck and the vertical side walls of the skylight curb or chimney. That critical transition relies on a layered metal waterproofing system called step flashing—and when even one piece is misinstalled, rusted, or smothered in roof cement, rain finds an easy path straight into your attic.

How Step Flashing Protects Roof Penetrations

Any time a structure punches through a sloped roof—whether it is a brick chimney, a site-built skylight curb, or a dormer wall—water flowing down the shingles slams into the sides of that vertical surface. A single flat strip of metal cannot seal a sloped intersection effectively because shingles overlap in stepped courses from the eaves to the ridge.
Instead, roofers weave individual L-shaped pieces of corrosion-resistant metal—typically galvanized steel, aluminum, or copper—between every single course of shingles. Each piece bends at a 90-degree angle: one leg lies flat over the underlying shingle course and beneath the next shingle up, while the vertical leg extends up against the side wall of the chimney or skylight frame.
Because each L-shaped shingle-height flashing overlaps the piece directly below it by at least two to three inches, water running down the vertical side wall sheds onto the horizontal leg and channels smoothly back onto the top surface of the shingles below. On masonry chimneys, a second overlapping layer called counterflashing is embedded directly into the brick mortar joints and folded down over the top edge of the step flashing, allowing the roof deck and chimney to expand, contract, and settle independently without tearing the waterproof seal.

Why Step Flashing Fails Long Before Skylight Glass

Modern insulated skylight glazing is factory-sealed with durable perimeter gaskets, weep channels, and tempered or laminated glass built to withstand decades of ultraviolet exposure and hail. By contrast, step flashing sits in the highest-traffic drainage zone on the roof, enduring thermal movement, wind-driven rain, ice buildup, and occasional installation shortcuts.

Relying on Roof Cement Instead of Proper Metal Layering

The single most common mistake found during leak inspections is a thick smear of black asphalt roof cement or silicone caulk troweled along the edge of a chimney or skylight. Homeowners and inexperienced handymen often treat sealant as a permanent fix, slathering mastic over exposed nails or gaps where metal meets masonry.
Outdoors, constant sun exposure and seasonal temperature swings dry out roof cement within a year or two, causing it to shrink, crack, and pull away from brick or wood. Worse, thick blobs of caulk act like tiny dams along the side of a skylight or chimney, trapping water behind them and forcing moisture sideways under the shingles rather than letting it drain freely down the roof slope.

Reusing Old Flashing During a Roof Replacement

When a home gets a new shingle roof, skipping new step flashing is an easy way for a low-bid contractor to shave labor hours. Old step flashing often hides beneath the siding or counterflashing, making it tempting to leave bent, nail-punctured metal in place and lay fresh shingles over top.
However, pulling off old shingles inevitably bends existing flashing legs, leaves behind dozens of unsealed nail holes, and misaligns the metal pieces with the exposure lines of the new shingles. Even a single stray nail driven too close to the bend in a step flashing piece creates a direct pinhole leak that drips silently onto the roof decking every time rain blows sideways.

Missing Kickout Flashing at Bottom Corners

At the lower corners where a chimney or skylight meets the downward slope of the roof, water channeled along the step flashing has to exit safely back onto the shingles. Without a properly shaped kickout flashing—or apron flashing cleanly integrated with the bottom step piece—concentrated runoff can curl around the lower corner and slip behind siding, wood trim, or underlayment.

Ice Dams and Debris Buildup Along Curb Sides

Skylights and chimneys interrupt smooth airflow and snow slide across a roof plane. Leaves, pine needles, and dirt collect rapidly in the narrow channel beside a skylight curb or behind a chimney, holding damp debris against the metal flashing and accelerating rust or galvanic corrosion where incompatible metals touch.
In cold climates, heat escaping around a skylight shaft or chimney chase melts snow directly above the penetration. That meltwater refreezes as soon as it hits the colder roof deck below, forming an ice dam that backs standing water upward beneath the overlapping step flashing legs—an upward flow that gravity-dependent shingle laps were never designed to resist without ice-and-water shield membrane underneath.

What About the Upper Edge of a Chimney or Skylight?

While step flashing guards the two sloped sides, the uphill side facing the ridge faces the full force of water cascading down the upper roof slope. On narrow skylights, a head flashing pan with upturned side dams diverts water around the left and right edges into the step flashing system.
On wider chimneys—generally those spanning 30 inches or more across the slope—standard flat flashing is not enough. Building codes and roofing best practices call for a cricket (also called a saddle): a small, peaked mini-roof built directly behind the chimney that splits oncoming water and debris cleanly to either side so water never pools against the uphill brickwork.

Clues That Point to Flashing Rather Than Glass Failure

Before replacing an entire skylight or paying for extensive masonry rebuilding, look closely at how and when the leak behaves:
  • Leaks during wind-driven rain: If water appears only when rain blows from a specific direction—rather than during gentle, vertical showers—wind is likely driving water up under loose step flashing or unsealed counterflashing.

  • Staining on the drywall shaft walls: Moisture discoloring the painted drywall sides of a skylight tunnel—especially near the corners—almost always traces back to curb step flashing or apron flashing rather than the glass seal above.

  • Dampness near the bottom edge of the frame: When condensation forms on cold interior glass during winter, droplets run down the pane and collect cleanly along the bottom sill; intermittent staining higher up the framing points to exterior flashing intrusion.

  • Peeling paint or efflorescence beside an interior chimney chase: White chalky mineral deposits on interior brick or damp drywall flanking a fireplace usually indicate failed step flashing, missing counterflashing, or an absent chimney cricket.

How Roofers Properly Repair Failing Step Flashing

Fixing a step flashing leak properly means removing the shingles immediately flanking the skylight or chimney down to the bare roof decking—never burying the problem under another layer of sealant. Once the area is stripped, roofers install a self-adhering ice-and-water barrier membrane up the vertical sides of the skylight curb or chimney base and across the surrounding deck.
From there, new step flashing pieces are woven one by one with fresh shingles from the bottom apron up to the head flashing or cricket, using corrosion-resistant fasteners placed high and away from the water channel. Around brick chimneys, the counterflashing is freshly regrooved into the mortar joints and sealed with durable polyurethane masonry sealant—creating a flexible, mechanical watershed built to outlast the shingles around it.

Comments are closed.